Ezstepper被设计为允许在产品需要自动化的解决方案的快速实施。
尺寸2“（50mm）直径，完全智能步进电机+驱动程序被设计成装在步进马达的背面上。一个单4线总线，包含2个电源线和两条通信线，在菊花链中连接多达16个这样的步进电机控制器。命令可以从任何串口终端程序发布（如超级终端）或从ezstepper Windows应用程序。
这些命令直观而简单。例如，命令万将步进电机的绝对位置10000。（这种通信协议与使用cavro DT或OEM协议兼容的设备）
EZ控制器还可以独立运行，不需要连接到PC。它可以设置为在开机时执行预设的指令串(即，在此模式下只需要电源)这些指令包括嵌套循环和暂停执行等待开关关闭，这在独立应用中非常有用。
Ez23的步进电机控制器将与任何步进电机是4英寸或更小的工作（size34或更小）。我们的初学者工具包使初次用户能够在半小时内学会使用智能驱动器来控制步进马达。
特性
单4线总线连接到16步进电机
3安培斩波（PWM）驱动器
供电12V至40V
RS232、RS485或usb通信
用于用户程序存储的EEPROM
单机操作，不连接PC机
执行停止/分支挂起开关关闭
预接线的optoswitch输入（见接线图）
适合大小23步进机的背面
多达256个微步/步双极控制
工业标准通信协议
一个命令的光电开关闭合开关
完全可编程的斜坡和速度
四个数字输入输出和两个1安培功率开/关驱动程序
软件可选的“移动”和“保持”电流
保持在移动完成时自动选择的电流
开关可选择地址
孔在PCB中心允许使用双轴电机
The EZStepper was designed to allow the rapid implementation of stepper motor solutions in products requiring automation.
Measuring only 2" (50mm) diameter, the fully intelligent stepper motor Controller + Drivers are designed to be bolted onto the back of the stepper motors that they control. A single 4 wire bus, containing 2 power wires and two communications wires, links up to 16 such stepper motor controllers in a daisy chain. Commands can be issued from any serial terminal program (such asHyperTerminal) or from the EZStepper Windows application.
The Commands are intuitive and simple. For example, the command A10000 will move the stepper motor to Absolute position10000. (This communications protocol is compatible with devices that use the Cavro DT or OEM protocol.)
The EZStepper is also capable of stand-alone operation with no connection to a PC. It can be set to execute a preset string of commands upon power up (i.e., only power is required in this mode). The Commands include nested loops and execution halt pending a switch closure, which is useful in stand-alone applications.
The EZ23 Stepper Motor Controller will work with any stepper motor that is 4" or smaller (size34 or smaller). Our Starter Kitsenable a first time user to make a Stepper Motor move intelligently in less than half an hour.
Features
Single 4 wire bus linking up to 16 stepper motors
3 Amp Chopper (PWM) Driver
Operates from 12V to 40V
RS232, RS485 or USB based Communications
On Board EEPROM For User Program storage
Stand alone operation with no connection to a PC
Execution Halt / Branch pending switch closure
Pre-wired for OptoSwitch inputs (see wiring diagram)
Fits on the back of a size 23 stepper
Up to 256 micro steps/step bipolar control
Industry standard communications protocol
Homes to an Opto or Switch closure with a single command
Fully programmable ramps and speeds
Four Digital I/O and two 1 Amp Power On/Off Drivers included
Software selectable "Move" and "Hold" currents
Hold Current automatically selected upon move completion
Hole in PCB allows use of double shafted motors
Ezstepper被设计为允许在产品需要自动化的解决方案的快速实施。
尺寸2“（50mm）直径，完全智能步进电机+驱动程序被设计成装在步进马达的背面上。一个单4线总线，包含2个电源线和两条通信线，在菊花链中连接多达16个这样的步进电机控制器。命令可以从任何串口终端程序发布（如超级终端）或从ezstepper Windows应用程序。
这些命令直观而简单。例如，命令万将步进电机的绝对位置10000。（这种通信协议与使用cavro DT或OEM协议兼容的设备）
EZ控制器还可以独立运行，不需要连接到PC。它可以设置为在开机时执行预设的指令串(即，在此模式下只需要电源)这些指令包括嵌套循环和暂停执行等待开关关闭，这在独立应用中非常有用。
Ez23的步进电机控制器将与任何步进电机是4英寸或更小的工作（size34或更小）。我们的初学者工具包使初次用户能够在半小时内学会使用智能驱动器来控制步进马达。
特性
单4线总线连接到16步进电机
3安培斩波（PWM）驱动器
供电12V至40V
RS232、RS485或usb通信
用于用户程序存储的EEPROM
单机操作，不连接PC机
执行停止/分支挂起开关关闭
预接线的optoswitch输入（见接线图）
适合大小23步进机的背面
多达256个微步/步双极控制
工业标准通信协议
一个命令的光电开关闭合开关
完全可编程的斜坡和速度
四个数字输入输出和两个1安培功率开/关驱动程序
软件可选的“移动”和“保持”电流
保持在移动完成时自动选择的电流
开关可选择地址
孔在PCB中心允许使用双轴电机
The EZStepper was designed to allow the rapid implementation of stepper motor solutions in products requiring automation.
Measuring only 2" (50mm) diameter, the fully intelligent stepper motor Controller + Drivers are designed to be bolted onto the back of the stepper motors that they control. A single 4 wire bus, containing 2 power wires and two communications wires, links up to 16 such stepper motor controllers in a daisy chain. Commands can be issued from any serial terminal program (such asHyperTerminal) or from the EZStepper Windows application.
The Commands are intuitive and simple. For example, the command A10000 will move the stepper motor to Absolute position10000. (This communications protocol is compatible with devices that use the Cavro DT or OEM protocol.)
The EZStepper is also capable of stand-alone operation with no connection to a PC. It can be set to execute a preset string of commands upon power up (i.e., only power is required in this mode). The Commands include nested loops and execution halt pending a switch closure, which is useful in stand-alone applications.
The EZ23 Stepper Motor Controller will work with any stepper motor that is 4" or smaller (size34 or smaller). Our Starter Kitsenable a first time user to make a Stepper Motor move intelligently in less than half an hour.
Features
Single 4 wire bus linking up to 16 stepper motors
3 Amp Chopper (PWM) Driver
Operates from 12V to 40V
RS232, RS485 or USB based Communications
On Board EEPROM For User Program storage
Stand alone operation with no connection to a PC
Execution Halt / Branch pending switch closure
Pre-wired for OptoSwitch inputs (see wiring diagram)
Fits on the back of a size 23 stepper
Up to 256 micro steps/step bipolar control
Industry standard communications protocol
Homes to an Opto or Switch closure with a single command
Fully programmable ramps and speeds
Four Digital I/O and two 1 Amp Power On/Off Drivers included
Software selectable "Move" and "Hold" currents
Hold Current automatically selected upon move completion
Hole in PCB allows use of double shafted motors
在线客服
